Disk (Plate) Cam Profile Calculator: Pressure Angle, Radius of Curvature, Undercut, Follower Spring Force and Camshaft Torque, Conjugate and Internal Cams, with DXF and CSV Export and a Printable Data Sheet

Disk (Plate) Cam Designer
Cam, Follower & Spring
Cam
rpm
mm
°
Follower
mm
mm
mm
mm
mm
in
kg
Spring & Load
N/mm
N
N
–
in
in
in
°

With conjugate cams there is no spring: the follower force is mass × acceleration plus the external load. Cam 1 carries it when it pushes the follower out and cam 2 when it pulls it back.

In a groove there is no spring: the follower force is mass × acceleration plus the external load, and the roller presses on whichever wall that force points to.

Swinging arm: segment lifts are arm angles in degrees. Enter mass and load as felt at the roller, along its arc: equivalent mass = arm inertia about the pivot ÷ (arm length)². Enter a compression spring's own rate and preload and where it pushes on the arm (Spring at); a torsion spring's rate ÷ (arm length)², with Spring at blank. Switching follower type converts the lifts using the arm length.

Internal cam: the roller runs inside a track cut into the cam face. Lift is measured toward the shaft, and the spring pushes the roller outward against the track. The track depth, floor and rim are set in the 3D Exports block.

Motion: Segments Over One Turn
#TypeStartEnd (°)Motion lawLift (mm)
Compare motion laws
Results
0°

campitch curvebase circleline of force

Warnings & Status

    2D & CAD Exports
    °
    in
    °
    in
    CSV COLUMNS

    Units: the DXF, curve and unwrapped files use the CAD file units above (mm unless you change it), and the unit is in each file name. Curve files (.sldcrv and .txt) carry no units: SolidWorks reads the numbers in the part's units, so the part must use the same units as the file. The CSV uses the page units. Curve: .sldcrv is the same text as .txt, named so it shows in SolidWorks' file dialog. Use Insert › Curve › Curve Through XYZ Points, Browse, then sketch on the plane at that Z, Convert Entities on the curve and extrude. 1° spacing (360 points) is plenty for most cams and keeps the spline light. If SolidWorks says the curve is self-intersecting, export again with Repeat first point off and close the small gap in the sketch. Unwrapped profile: a flat line from 0 to 2π × the wrap radius, with the chosen height above it. Wrap only takes closed sketches, so close it first: for a groove, offset the line by the roller radius to both sides and cap the ends. Sketch on a plane tangent to a cylinder of that radius and use Wrap (Deboss cuts a groove). DXF: closed cam profile, pitch curve and base circle, plus the groove's outer wall and the blank for a face cam, or cam 2's profile and pitch curve for a conjugate pair. SolidWorks brings the DXF in as many short straight lines; use the curve file when you want a smooth spline.

    3D Exports
    in
    °
    in
    in
    in
    ×
    in

    Both files are in millimetres, whichever units are selected. STL has no units of its own and slicers read it as mm. In SolidWorks, pick millimetres when opening the STL. The first STEP export downloads the CAD kernel (about 50 MB). Both use the point spacing above.

    Graphs

    Negative values are concave parts of the cam. Very large values (nearly flat) are left off the plot.

    Below zero the spring cannot hold the follower on the cam.

    3D Model

    Drag to orbit, scroll to zoom. Shows the part as it will export, including the scale.

    Print Data Sheet prints the cam on three pages: a scale drawing with the inputs, motion program, results and checks; the motion and force graphs; and a point table every 10°. Pressing Ctrl+P on this page prints the same sheet.

    Running several cams on one shaft? Line them up on the cam timing diagram: save this cam with Export, then use Add Cam From File there.

    New to cams? Start with the cam design guide.

    For critical applications, check the results by hand or with another cam program. This is a free calculator and is not liable for design errors.

    Forces assume a rigid follower train and no friction. Contact stress assumes steel on steel. For a cylinder or a sliding plate, use the barrel or linear cam designer.

    Reference Guide: Disk Cam Design
    01

    Follower Types

    Roller

    The most common choice. Rolling contact means low friction and long life. The roller centre follows the pitch curve; the cam surface sits one roller radius inside it.

    Knife-edge

    A roller of zero radius. Fine for slow, light work and for checking a motion. It wears fast.

    Flat-face

    A flat plate on the follower stem. The pressure angle is zero, so the cam puts no side load on the stem. The cam must be convex everywhere, and the face must be wide enough for the contact point to travel.

    Swinging arm

    A roller on a lever arm that pivots. The lift is an angle. Because the roller moves on an arc, the pressure angle is not zero even on a dwell, and the limit is a little higher, about 35° (Norton, p. 152). The tool finds the arm angle, pressure angle and curvature from the geometry and matches Norton's Eqs. 7.8a–d. Put the pivot so the arm is roughly square to the line from the cam centre at mid-swing for the lowest pressure angles.

    Offset

    Moving a translating follower sideways from the cam centre lowers the pressure angle on one stroke and raises it on the other. Use it when the rise is the hard stroke.

    02

    Base Circle and Prime Circle

    The base circle is the smallest circle that touches the cam surface. The follower sits on it in the low dwell. The prime circle is the base circle plus the roller radius. The roller centre runs on it in the low dwell.

    A bigger base circle lowers the pressure angle and raises the radius of curvature, at the cost of a bigger, heavier cam. The results show the smallest base circle that meets your pressure angle limit.

    03

    Pressure Angle

    The pressure angle φ is the angle between the follower's direction of travel and the line of force at the contact. Only the part of the force along the follower does useful work. The rest pushes the stem sideways into its guide.

    Translating roller, offset e tan φ = (s′ − e) / (√(Rp² − e²) + s)

    s′ = ds/dθ in mm per radian (Norton, Eq. 7.3d). φ is positive on the rise. On a counter-clockwise cam a positive offset lowers the rise pressure angle and raises the fall one; a clockwise cam reverses this. The tool works φ out from the shape of the pitch curve and is tested against this equation.

    Typical limit: keep φ between 0 and about ±30° for translating followers (up to about ±35° with a low-friction ball slide), and up to about ±35° for swinging arms (Norton, pp. 152 and 531). These are rules of thumb, not a standard. Above them friction in the guide grows fast and the follower can jam: the normal force is N = F·b / (b cos φ − (2μa + μb − μ²d) sin φ) (Norton Eq. 7.1b), which becomes infinite as the denominator reaches zero.

    Normal force at the contact = follower force / cos φ.

    04

    Swinging Arms: Dragged or Pushed

    Two ways to arrange the same arm

    A swinging roller arm can sit on either side of the cam. Which side, together with the direction the cam turns, decides how the cam loads the arm:

    • Cam drags the arm: the cam surface under the roller moves away from the pivot. The arm is pulled, in tension. Norton Eq. 7.8a, "cam rotating away from the follower arm pivot" (p. 164).
    • Cam pushes the arm: the surface moves toward the pivot. The arm is pushed, in compression, like a strut. Norton Eq. 7.8b.

    The cam's motion and torque come out almost the same either way. What changes is the pressure angle. The two arrangements swap their worst angles between the rise and the return.

    Which is better

    For the usual layout, with the arm shorter than the distance from the cam centre to the pivot, the dragging arrangement has the lower pressure angle on the rise. The rise is the stroke where the cam does the work, lifting against the spring, the load and the inertia. On the return the spring drives the follower and the cam only guides it, so a higher angle there matters less. Dragging also keeps the arm in tension: if the roller skids, friction pulls the arm along instead of jamming it.

    The advantage is not a fixed rule. With an arm longer than the pivot distance it reverses, and the pushing arrangement has the lower rise angle. The results show which arrangement you have and the rise pressure angle with the pivot on the other side, and the status list suggests switching when the other side is lower.

    Example: the default cam on a 3 in arm, pivot 4 in from the cam centre
    ArrangementMax pressure angle, riseMax pressure angle, return
    Cam drags the arm18.9°25.4°
    Cam pushes the arm26.9°16.8°

    With a 100 mm arm and the pivot 90 mm away, the result flips: 44.0° on the rise when dragged, 29.7° when pushed.

    Spring part-way along the arm

    A compression spring usually pushes on the arm between the pivot and the roller. Enter its own rate and preload, and its distance a from the pivot in Spring at. The tool converts it to the roller, where the forces are computed. Equal moments about the pivot and equal work give:

    rate at roller = k·(a / l)²
    preload at roller = F0·(a / l)

    Here l is the arm length. A spring at half the arm length acts like one a quarter as stiff at the roller, with half the preload.

    05

    Radius of Curvature and Undercut

    Pitch curve, on-centre (Norton Eq. 7.10, Rothbart Eq. 6.22) ρ = (r² + s′²)3/2 / (r² + 2s′² − r·s″), r = Rp + s

    The cam surface radius is ρ − Rf on convex parts. If the pitch curve is sharper than the roller (0 < ρ < Rf), the cutter would gouge the profile. That is undercut, and the follower will not follow the motion you asked for.

    For a flat-face follower the cam's radius of curvature is ρ = Rb + s + s″. It must stay above zero, or the profile has a cusp. The worst point is where acceleration is most negative, so the smallest usable base circle is Rb > ρmin − s − a there (Norton Eq. 7.20). The results show it for ρmin = 0; add margin for contact stress.

    Rule of thumb: keep the smallest convex radius of the pitch curve at least 1.5 to 3 times the roller radius; above 2 is a good target (Norton, p. 166 and p. 531). The results show this as the curvature ratio. Fixes: a smaller roller, a bigger base circle, a longer rise angle, or a law with lower peak acceleration. Small radii also raise contact stress.
    06

    Follower Force, Spring and Torque

    Force the cam supplies along the follower (Norton Eq. 9.10) F = m·a + c·v + k·(s + δ₀) + Fext

    m is the moving mass, c the damping, k the spring rate and k·δ₀ the preload. You enter damping as a ratio ζ; the tool uses c = ζ·2√(k·m) (Norton Eqs. 9.2i, 9.3a). The natural frequency of the follower on its spring is fn = √(k/m) / 2π (Eq. 9.1d–e). If F drops below zero, the follower leaves the cam ("jump" or "float"). The status box says how much extra preload stops it. Size the spring on the compression spring calculator.

    With no friction, power in equals power out, so the camshaft torque is T = F·s′ (Norton Eq. 9.12). It goes negative when the follower drives the cam on the way down. Use the peak to size the shaft (minimum shaft diameter, keyway).

    Contact stress uses Hertz line contact between parallel cylinders, roller on cam, both steel (E = 207 GPa, ν = 0.3): half-width a = √(2(m₁ + m₂)F / (πBL)) and pmax = 2F/(πaL), with B = ½(1/Rroller + 1/ρcam) and m = (1 − ν²)/E (Norton Eqs. 12.14–12.15). The largest shear stress is below the surface, 0.304·pmax at a depth of 0.786·a (Eq. 12.17b). That is where pitting fatigue starts, so case-hardening must reach deeper than it. Check other materials on the Hertz contact stress page.

    Spring surge: keep the spring's natural frequency above about the 11th harmonic of the cam speed (9 at the lowest with a smooth motion law). Rothbart, p. 374.
    07

    Face (Groove) Cams

    What changes

    Set Closure to Groove to make a face cam. The roller runs in a groove cut into the face of the disk, so the cam drives the follower out and back and no spring is needed. The groove's inner wall is the ordinary cam profile. Its outer wall is the pitch curve offset outward by the roller radius.

    The motion, pressure angle and pitch curve are the same as for a spring-closed cam with the same base circle and roller.

    Checks

    Both walls must clear the roller. Where the pitch curve is concave (on the flanks of a steep rise) only the outer wall bends tighter than the roller, so a groove can undercut where a spring-closed cam would not. The curvature ratio and undercut check cover both walls.

    The follower force is mass × acceleration plus the external load. Where it changes sign the roller crosses to the other wall and takes up the clearance with a small knock (Norton §9.5, pp. 238–239). The results list how many wall changes happen per turn. Keep the clearance small, or use two rollers, one per wall.

    Groove depth = roller width + clearance under the roller. Thickness = depth + floor. Blank diameter = 2 × (widest outer wall radius + rim).
    08

    Conjugate (Double-Disk) Cams

    What they are

    A conjugate pair is two plate cams side by side on one shaft. The follower carries two rollers, one on each cam. Cam 1 pushes the follower out and cam 2 pulls it back, so no spring is needed and the follower cannot jump. Rothbart calls them conjugate, complementary or double-disk cams (Fig. 1.11, pp. 7–9) and lists them with grooved cams as the most common industrial production cams (p. 5).

    Compared with a face groove, each roller turns one way only, so there is no roller reversal at each crossover. The two cams are ground separately on their outsides, which avoids the groove-width and heat-treat distortion problems of a track (Norton §9.5, pp. 238–239). The price is two cams that must be made as a matched set.

    Set it up

    Set Closure to Conjugate. Cam 1 is the cam you design: base circle, roller, offset and motion. Cam 2 follows from it. With a sliding follower, roller 2 sits on the same line as roller 1, on the far side of the shaft, a fixed roller spacing away. With a swinging arm, the follower is a bell crank: arm 2 is fixed to arm 1 at the angle between the arms and points to the far side of the line from the pivot to the cam centre. Left blank, the spacing or angle is set so cam 2 comes out the same size as cam 1.

    How cam 2 is found

    Cam 2 is found the same way as cam 1, by kinematic inversion: hold the follower still, turn the shaft backwards, and trace roller 2's centre. That trace is cam 2's pitch curve. Cam 2's surface is that curve offset toward the shaft by roller 2's radius. Cam 2 gets its own pressure angle, radius of curvature and undercut checks, and the drawing shows it in purple behind cam 1.

    For an on-centre sliding follower, roller 2 runs at L − d − s from the shaft, where L is the roller spacing, d the prime circle radius and s the lift. Cam 2's pressure angle and radius of curvature then follow the same on-centre formulas as cam 1, with that radius in place of d + s.

    Forces

    With no spring, the follower force is mass × acceleration plus damping and any external load (Norton Eq. 9.11). Cam 1 carries it while it pushes the follower out, cam 2 while it pulls it back. On a bell crank, roller 2 carries roller 1's force × arm 1 ÷ arm 2. Where the force changes sign the load moves from one cam to the other, and any play closes with a small knock (crossover shock, Norton p. 238). Some designs spring the two rollers together to take up the play.

    Check: Norton's Example 9-3 (p. 240), run as a conjugate pair, gives a peak follower force of 288 lb (book: 287–289 lb) and a peak camshaft torque of 506 lb·in (book: 505 lb·in, Fig. 9-17b).
    09

    Internal Cams

    What changes

    Set Cam surface to Inside for an internal cam. The roller runs on the inside of a track cut into the face of the cam, like the outer wall of a face groove with no inner wall. The follower can be a sliding roller or a rocker arm that sits inside the track.

    The cam can only push the roller toward the shaft, so that is the direction of lift. A spring holds the roller out against the track. The base circle is the track at low dwell, which is its largest radius. The prime circle (the roller centre at low dwell) is the base circle minus the roller radius.

    Pressure angle

    The roller's distance from the shaft shrinks as it lifts, so an internal cam has a higher pressure angle than an outside cam with the same base circle and motion. For an on-centre sliding follower, tan φ = s′ ÷ (Rp − s). Use a bigger base circle or a longer rise to bring it down.

    With a rocker arm, the pressure angle is lowest where the arm is square to the line from the roller to the cam centre. The page's starting layout sets this at mid-lift: pivot distance² = (Rp − lift ÷ 2)² + arm length². That keeps the pivot inside the track.

    Curvature and undercut

    Where the pitch curve bulges outward, the track wraps round the roller (a concave contact). That is gentle on the roller and cannot undercut. Where the pitch curve bulges inward, the track is convex toward the roller with radius |ρpitch| − Rf. If that bend is tighter than the roller, the track undercuts and the follower misses part of its motion (Rothbart Fig. 6.10, p. 172). Rothbart notes that curvature is less critical in internal cams because the contact stresses are lower (p. 171). The curvature ratio on this page uses the tightest inward bulge.

    The part

    The 3D part is a round blank with the track pocketed into its face and the bore through the floor. Track depth = roller width + clearance under the roller. Automatic thickness = depth + floor. Blank diameter = 2 × (largest track radius + rim). The DXF holds the track, pitch curve, base circle, bore and blank.

    Check: for an on-centre sliding follower the page matches tan φ = s′ ÷ (Rp − s) and Rothbart Eq. 6.22 (p. 169) with r = Rp − s, at every degree.
    10

    Constant-Velocity Segments

    Some machines need the follower to move at a steady speed for part of the turn, for example to keep pace with a conveyor. Use a Constant velocity segment for that stretch. Its speed is lift ÷ angle. The segments on either side must speed up to it and slow down from it without a jump.

    Polynomial, blends to its neighbours

    Pick this law for the segment before or after. It reads the speed and acceleration where its neighbours end and fits a 5th-degree polynomial that matches both, with no end conditions to type. Norton's Example 6-2 (p. 133) does a whole cam this way: a 180° constant-velocity rise and one blending fall.

    Half-cycloids

    Half-cycloid, into constant velocity starts at rest and ends at speed; out of constant velocity does the reverse. Acceleration is zero at both ends, so they join a constant-velocity segment smoothly (Norton Eqs. 6.3–6.4). The lift must suit the speed: lift = β × v ÷ 2, with β in radians and v the constant velocity in length per radian. The status box flags any join where the speeds don't match.

    Skewed laws and cycloidal–harmonic

    Most laws show a peak v at box under the law. It moves the peak velocity earlier or later in the segment; 0.5 is the standard law. On a spring-loaded rise, 0.25 makes the deceleration a third of the acceleration, so a smaller spring holds the follower (Rothbart §3.2 and §3.6). Cycloidal–harmonic ends decelerating, so put it before a return, not a dwell; harmonic–cycloidal is its mirror for the return. See the cam motion laws page for the equations.

    Norton's advice: use as few segments as you can. His two-segment polynomial design had lower acceleration than his four-segment one.
    11

    Export and Machining Notes

    The DXF holds the cam profile as one closed polyline of short straight lines, one per point spacing (0.5° unless you change it), plus the pitch curve and base circle on their own layers. For a 40 mm base circle at 0.5° the chord error is under 1 µm. The file is in the CAD file units chosen in the export block, and the unit is in its name.

    The 3D exports make the cam plate with a plain round bore and no keyway. The default bore is 10% of the mean cam diameter, rounded to the nearest 1/16 in. STEP side faces are B-splines fitted to the profile, one per motion segment and no more than 60° each. The export scale changes every dimension equally, which suits 3D-print fit tuning. It is not a substitute for machining tolerances. Phase turns every 2D and 3D export about the cam centre (positive = clockwise seen from +Z), for example to line the cam up with a keyway or a tilted follower in an assembly.

    Machine the cam with a cutter no larger than twice the smallest concave radius. The project file (Export) holds the whole design and opens on every KasperCalc cam page.

    The printed data sheet is for checking and records. Its drawing has a scale bar, so you can measure from it even when the printer shrinks the page. Its point table every 10° is for spot checks on the finished cam; cut from the CAD files, which hold every point.

    12

    Example Cam, Every 10°

    The calculator's starting example, in round inch values: base circle radius 1.5 in (38.1 mm), 1 in diameter roller (½ in radius, ⅝ in wide) on centre, cycloidal rise of 1 in (25.4 mm) over 0–120°, dwell to 180°, modified-sine fall to 300°, dwell to 360°. 120 rpm, 1.5 lb (0.68 kg) follower, 25 lbf/in (4.38 N/mm) spring with 10 lbf (44.5 N) preload, damping ratio 0.10.

    θ (°)Lift (in)Lift (mm)Velocity (in/s)Accel. (in/s²)Pressure angle (°)Cam radius of curvature (in)Contact force (lbf)Torque (lbf·in)
    00.00000.000.000.00.001.50010.000.00
    100.00380.100.80113.11.832.61310.580.68
    200.02880.733.00195.96.714.47611.672.79
    300.09082.316.00226.212.864.88313.526.46
    400.19554.979.00195.918.073.44416.2111.61
    500.33718.5611.20113.120.872.41119.5617.43
    600.500012.7012.000.020.911.87423.2522.20
    700.662916.8411.20-113.118.501.59226.8323.91
    800.804520.439.00-195.914.331.46029.9121.42
    900.909223.096.00-226.29.321.45832.2215.39
    1000.971224.673.00-195.94.591.59733.718.05
    1100.996225.300.80-113.11.221.91834.522.21
    1201.000025.400.000.00.002.50035.000.00
    1301.000025.400.000.00.002.50035.000.00
    1401.000025.400.000.00.002.50035.000.00
    1501.000025.400.000.00.002.50035.000.00
    1601.000025.400.000.00.002.50035.000.00
    1701.000025.400.000.00.002.50035.000.00
    1801.000025.400.000.00.002.50035.000.00
    1900.993725.24-1.32-172.3-2.011.69434.09-3.58
    2000.956924.31-4.01-196.0-6.171.58532.91-10.51
    2100.882822.42-6.60-172.3-10.321.59530.99-16.27
    2200.775819.71-8.71-127.9-14.011.64628.36-19.64
    2300.644416.37-10.08-68.1-16.871.74025.22-20.23
    2400.500012.70-10.560.0-18.581.89421.84-18.35
    2500.35569.03-10.0868.1-18.812.14718.53-14.86
    2600.22425.69-8.71127.9-17.302.58015.56-10.78
    2700.11722.98-6.60172.3-13.933.31113.19-6.92
    2800.04311.09-4.01196.0-8.894.29911.59-3.70
    2900.00630.16-1.32172.3-3.003.86510.75-1.13
    3000.00000.000.000.00.001.50010.000.00
    3100.00000.000.000.00.001.50010.000.00
    3200.00000.000.000.00.001.50010.000.00
    3300.00000.000.000.00.001.50010.000.00
    3400.00000.000.000.00.001.50010.000.00
    3500.00000.000.000.00.001.50010.000.00
    13

    Sources

    H. A. Rothbart (ed.), Cam Design Handbook, McGraw-Hill, 2004: conjugate cams (pp. 5–9, Fig. 1.11, and Fig. 10.22c, p. 311), radius of curvature Eq. 6.22 (p. 169), curvature of internal cams and undercut (p. 171, Fig. 6.10), pressure angle §7.2.2 (p. 179), spring surge §12.3.5.3 (p. 374), and the motion laws listed on the cam motion laws page.

    The geometry is computed by kinematic inversion from exact derivatives of the motion. The on-centre radius of curvature matches Rothbart Eq. 6.22 and the pressure angle matches the closed form above. The 3-4-5-6 rise–fall segment follows R. L. Norton, Cam Design and Manufacturing Handbook, Eq. 4.2 (p. 62). Norton's Chapter 7 pressure-angle equation (Eq. 7.3d, p. 156) and sign convention (p. 157), pitch-curve coordinates (Eq. 7.11, p. 169) and radius of curvature (Eq. 7.10, p. 167) all match, and the curvature ratio follows his rule on pp. 166 and 531. Form-closed and conjugate cams follow his §9.5 and Fig. 9-15 (pp. 238–239). His Examples 9-2 and 9-3 (pp. 234–242), an eight-segment cam at 18.85 rad/s, are reproduced: peak acceleration 3504 in/s², pressure angle 29.2°, minimum radius 1.7 in, spring force 400.4 lb peak, desmodromic force 289 lb, and camshaft torque 729 and 505 lb·in. Contact stress follows his Example 12-2 (pp. 361–363): 90,946 psi peak and 27,648 psi shear at 0.003 in deep.