Barrel (Cylindrical) and End Cam Calculator: Groove Pressure Angle, Radius of Curvature, Undercut, Follower Force and Camshaft Torque, with STEP, STL, DXF and SolidWorks Curve Export

Barrel (Cylindrical) and End Cam Designer
Cylinder, Follower & Load
Cam
rpm
in
in
in
in
°
Follower
in
in
in
lb
Spring & Load
lbf/in
lbf
lbf
–

In a groove there is no spring: the follower force is mass × acceleration plus the external load, and the roller presses on whichever wall that force points to.

Motion: Segments Over One Turn
#TypeStartEnd (°)Motion lawLift (mm)
Compare motion laws
Results
0°

groove wallspitch line (roller centre)line of force

Warnings & Status

    2D & CAD Exports
    °
    in
    °
    in
    CSV COLUMNS

    Units: the DXF and curve files use the CAD file units above (mm unless you change it), and the unit is in each file name. Curve files carry no units: SolidWorks reads them in the part's units. Three ways to make the groove in SolidWorks: (1) Open the STEP below: it has the true roller-swept walls. (2) Wrap: make a cylinder of the outer radius, sketch the unrolled groove (DXF or curve) on a plane tangent to it, and Wrap › Deboss to the groove depth. Wrap cuts walls square to the surface, so they match the roller exactly at the surface and drift slightly toward the floor where the groove is steep. (3) Sweep cut: Insert › Curve › Curve Through XYZ Points with the pitch curve, then sweep the roller's rectangle along it. The DXF holds the unrolled groove outline (closed, ready for Wrap), the pitch line and the cylinder surface outline. Unrolled x runs along the cam angle; if the groove comes out mirrored in CAD, flip the sketch.

    3D Exports
    in
    °
    ×

    Both files are in millimetres, whichever units are selected. The cylinder's axis is Z, from Z = 0 to its length, with the follower on the +X side. STEP: the groove is cut with a loft through the exact wall points, one section every 2° (or the point spacing, if coarser). It takes a few seconds, and the first export downloads the CAD kernel (about 50 MB).

    Graphs

    Negative values are concave parts of the cam. Very large values (nearly flat) are left off the plot.

    For a groove, below zero means the roller presses on the other wall.

    3D Model

    Drag to orbit, scroll to zoom. Shows the part as it will export, including the scale.

    Print Data Sheet prints the cam on three pages: a scale drawing with the inputs, motion program, results and checks; the motion and force graphs; and a point table every 10°. Pressing Ctrl+P on this page prints the same sheet.

    Running several cams on one shaft? Line them up on the cam timing diagram: save this cam with Export, then use Add Cam From File there.

    New to cams? Start with the cam design guide. Disk cams: disk cam designer. Plates: linear cam designer.

    For critical applications, check the results by hand or with another cam program. This is a free calculator and is not liable for design errors.

    Forces assume a rigid follower train and no friction. Contact stress assumes steel on steel and a cylindrical roller.

    Reference Guide: Barrel Cam Design
    01

    What a Barrel Cam Is

    The part

    A barrel (cylindrical) cam is a cylinder with a groove cut round its surface. The follower slides parallel to the cylinder's axis. Its roller sits in the groove with the roller's own axis pointing at the cam axis. As the cylinder turns, the groove pushes the follower back and forth.

    Barrel cams suit long strokes along a shaft: indexers, pick-and-place heads, winding traverses and machine-tool feeds.

    What the tool assumes

    A translating roller follower with no offset. Norton notes that a flat-face follower cannot run on a barrel cam, and that offsetting the roller gives no benefit (§7.2, p. 158). Swinging-arm barrel followers are not covered yet.

    The groove is the lift diagram wrapped round the cylinder. Unroll the cylinder and the groove's centre line is the lift curve, stretched so that one turn equals the circumference.

    02

    Pressure Angle

    The pressure angle is the angle between the follower's line of travel and the push from the groove wall. Because the unrolled groove is the lift curve, the angle comes straight from its slope (Norton Eq. 7.4, p. 158):

    φ = atan(V / (ω·Rp)) = atan(s′ / Rp)

    V is the follower velocity, ω the cam speed in rad/s, and s′ the lift per radian of cam turn. Rp is the pitch radius: the radius at the middle of the roller's contact length.

    It changes with depth

    The roller touches the wall from the outer surface down to its inner end. Nearer the axis the circumference is shorter, so the same lift is steeper. The tool reports Norton's value at Rp and also the value at the roller's inner end. Size the follower guide for the larger one.

    To lower it: use a bigger cylinder, or spread the rise over more of the turn. The tool shows the smallest outer radius that holds your limit.

    03

    Radius of Curvature and Undercut

    The groove's centre line, unrolled at Rp, has radius of curvature (Norton Eq. 7.21, p. 173):

    ρ = −[1 + (V/(ωRp))²]3/2 / (A / (ω²Rp²))

    A is the follower acceleration. On a dwell the acceleration is zero and ρ is infinite (a straight groove).

    Both walls count

    A groove has two walls. Where the centre line bends, one wall is convex with radius ρ − Rf and the other concave. If |ρ| is smaller than the roller radius anywhere, a wall folds over itself: undercut. Norton keeps |ρ| at 1.5 to 3 times the roller radius, above 2 by preference (p. 166 and rule 7, p. 531). The tool reports this ratio and flags undercut.

    04

    Groove or Spring Closure

    Groove (form closed)

    Most barrel cams are grooved, so the cam drives the follower both ways and no spring is needed. The follower force is then mass × acceleration plus any external load. When that force changes sign, the roller moves across to the other wall. It crosses the clearance and lands with a small knock (Norton §9.5, pp. 238–239).

    The tool lists where these wall changes happen. Keep the clearance small, run the cam slower, or use two rollers, one per wall, to remove the knock.

    Spring (open track)

    With an open track or rib, a spring holds the roller on one side. The force check is the same as for a disk cam: the contact force must stay above zero. The tool shows how much more preload is needed if it does not.

    05

    End Cams

    The part

    An end cam has its profile cut on the end of a tube. The follower slides parallel to the axis, its roller rides on the end face, and a spring holds it there. It suits short strokes on a shaft where there is no room for a disk, such as feeds, clamps and valve lifters.

    Set Cam form to End cam. The face is the lower wall of the matching barrel groove, so the pressure angle and curvature are the same as for a barrel cam of the same size.

    Sizes and checks

    The face runs from the inner radius to the outer radius. By default the inner radius is the roller's inner end less the clearance, so the whole roller length rests on the face. Base height is the solid tube left under the lowest point of the face.

    Being one-sided, an end cam needs its spring: the contact force must stay above zero, or the roller lifts off the face. The force check and the extra preload it needs work as on the disk page.

    06

    Roller Length and Skidding

    A plain cylindrical roller in a barrel groove cannot roll perfectly. The groove wall moves faster at the outer surface than at the bottom, but every point on the roller turns at the same speed. So part of the roller skids. Longer rollers in deeper grooves skid more.

    Common fixes are a short roller, or a conical roller whose cone apex sits on the cam axis, so its surface speed matches the wall at every depth. This calculator models a cylindrical roller.

    07

    Forces, Torque and Contact Stress

    Follower force along its line of travel:

    F = m·a + c·v + k·s + F0 + Fext

    For a groove, k and F0 are zero. The force normal to the wall is F / cos φ. Camshaft torque comes from power balance: T = F·s′ = F·tan φ·Rp.

    Contact stress treats the roller as a cylinder pressed on the loaded wall, whose radius is ρ − Rf on one side and −ρ − Rf on the other (Norton's line-contact equations, Ch. 12). Treat it as approximate: contact along a radial roller in a curved groove is close to, but not exactly, a line.

    08

    CAD Export Notes

    The STEP file is a true solid: a cylinder with a bore, and the groove cut by a loft through the exact wall points. At each radius the wall is the lift curve unrolled at that radius and offset by the roller radius, which is what a radial roller (or an end mill of the same size) sweeps out.

    The STL is a closed mesh of the same walls. Its volume is within 0.2% of the exact value at the default point spacing.

    Handedness: the follower is on the +X side, looking from +Z. A counter-clockwise barrel needs the mirror image of a clockwise one. Check the rotation before exporting.

    Phase turns the part about Z, for example to line the groove up with a keyway in your assembly.

    End cams export the same way: the STEP is the tube with the exact roller-swept face, and the unrolled DXF and curve files hold the face at the outer radius, closed down to the base.

    09

    Example Cam, Every 10°

    The calculator's starting example: 2 in (50.8 mm) outer radius, ¾ in roller ½ in long with 1/16 in under it, so Rp = 1.75 in. Cycloidal rise of 1 in (25.4 mm) over 0–120°, dwell to 180°, modified-sine fall to 300°, dwell to 360°. 120 rpm, 1.5 lb (0.68 kg) follower, groove closure.

    θ (°)Lift (in)Lift (mm)Velocity (in/s)Accel. (in/s²)Pressure angle (°)Pitch radius of curvature (in)Follower force (lbf)Torque (lbf·in)
    00.00000.000.000.00.00—0.000.00
    100.00380.100.80113.12.09-4.2850.440.03
    200.02880.733.00195.97.77-2.5380.760.18
    300.09082.316.00226.215.26-2.3810.880.42
    400.19554.979.00195.922.26-3.1140.760.55
    500.33718.5611.20113.126.98-6.0420.440.39
    600.500012.7012.000.028.62—0.000.00
    700.662916.8411.20-113.126.986.042-0.44-0.39
    800.804520.439.00-195.922.263.114-0.76-0.55
    900.909223.096.00-226.215.262.381-0.88-0.42
    1000.971224.673.00-195.97.772.538-0.76-0.18
    1100.996225.300.80-113.12.094.285-0.44-0.03
    1201.000025.400.000.00.00—0.000.00
    1301.000025.400.000.00.00—0.000.00
    1401.000025.400.000.00.00—0.000.00
    1501.000025.400.000.00.00—0.000.00
    1601.000025.400.000.00.00—0.000.00
    1701.000025.400.000.00.00—0.000.00
    1801.000025.400.000.00.00—0.000.00
    1900.993725.24-1.32-172.3-3.432.821-0.670.07
    2000.956924.31-4.01-196.0-10.352.592-0.760.24
    2100.882822.42-6.60-172.3-16.703.193-0.670.35
    2200.775819.71-8.71-127.9-21.604.703-0.500.34
    2300.644416.37-10.08-68.1-24.639.458-0.260.21
    2400.500012.70-10.560.0-25.64—0.000.00
    2500.35569.03-10.0868.1-24.63-9.4580.26-0.21
    2600.22425.69-8.71127.9-21.60-4.7030.50-0.34
    2700.11722.98-6.60172.3-16.70-3.1930.67-0.35
    2800.04311.09-4.01196.0-10.35-2.5920.76-0.24
    2900.00630.16-1.32172.3-3.43-2.8210.67-0.07
    3000.00000.000.000.00.00—0.000.00
    3100.00000.000.000.00.00—0.000.00
    3200.00000.000.000.00.00—0.000.00
    3300.00000.000.000.00.00—0.000.00
    3400.00000.000.000.00.00—0.000.00
    3500.00000.000.000.00.00—0.000.00
    10

    Sources

    R. L. Norton, Cam Design and Manufacturing Handbook: barrel cam pressure angle Eq. 7.4 (§7.2, p. 158), radius of curvature Eq. 7.21 (§7.8, p. 173), the curvature ratio rule (p. 166 and rule 7, p. 531), form-closed (groove) forces and crossover (§9.5, pp. 238–241), and the line-contact equations (Ch. 12). Motion laws: see the cam motion laws page.