Cam Design Guide: Types of Cams and Followers, Closure, Choosing a Motion Law, Design Steps and Glossary

Which Cam Tool Do I Need?
Start Here
You want to…Use
Compare motion laws (cycloidal, modified sine, 3-4-5 …) for one riseCam Motion Laws
Design a disk (plate) cam: profile, pressure angle, curvature, spring, DXFDisk Cam Designer
Size the follower springCompression Spring, Torsion Spring
Check roller contact stress for other materialsHertz Contact Stress
Size the camshaft and its keyMinimum Shaft Diameter, Keyway Design
Design a barrel (cylindrical) cam or an end cam: groove or face, pressure angle, STEPBarrel Cam Designer
Design a linear (translating) cam plate: profile, pressure angle, drive forceLinear Cam Designer
Time several cams on one machine: phase, ratio, dwell overlap, overlaid motionCam Timing Diagram

Every cam page saves the same project file, so a design started on one page opens on the others.

Reference Guide: Cam Design
01

Types of Cams

Disk (plate, radial) cam

A flat plate turning on a shaft. The follower moves in the plane of the plate, toward and away from the shaft. The most common cam and the cheapest to make.

Barrel (cylindrical, drum) cam

A groove cut around a cylinder. The follower moves parallel to the shaft. Good for long strokes and indexing, and the groove drives the follower both ways. Design one with the barrel cam designer.

End cam

The profile is cut on the end of a tube, and a spring holds the follower's roller on it. The follower moves parallel to the shaft. The barrel cam designer makes these too (Cam form: End cam).

Linear (wedge, translating) cam

A shaped plate that slides instead of turning. The follower rises and falls as the plate passes. Design one with the linear cam designer.

Face and grooved cams

A groove cut in the face of a disk. The roller rides in the groove, so no spring is needed. Used where the follower must never leave the cam. Design one in the disk cam designer with Closure set to Groove.

02

Types of Followers

By motion

Translating: slides in a straight line. On-centre if its line passes through the cam centre, offset if not.

Swinging (oscillating): a lever arm on a pivot. It tolerates larger pressure angles than a translating follower.

By contact

Roller: low friction, long life, the usual choice. Flat-face: no side thrust, but the cam must be convex everywhere. Knife-edge: follows any shape but wears fast. Mushroom (spherical): a curved face that tolerates misalignment.

03

Closure: Keeping the Follower on the Cam

Force closure (spring)

A spring, gravity or a load holds the follower against the cam. Simple and cheap. At high speed the spring must supply more force than the follower's inertia needs, or the follower lifts off ("jump" or "float").

Form closure (positive drive, desmodromic)

The cam's shape drives the follower both ways: a groove, two cams working as a conjugate pair, or a constant-breadth cam inside a yoke. No spring, no jump, but tighter tolerances and a load that swaps sides when acceleration changes sign.

Constant-breadth cams: the follower's two opposite contacts stay a fixed distance apart, so the motion must satisfy s(θ) + s(θ + 180°) = constant.
04

Choosing a Motion Law

The motion law sets how the follower gets from one position to the next. Between two dwells, pick a law whose velocity and acceleration both start and end at zero: cycloidal, modified sine, modified trapezoid, 3-4-5 or 4-5-6-7. That keeps the acceleration continuous (the "fundamental law of cam design").

NeedGood choiceWhy
Lowest force (heavy follower)Modified trapezoidLowest peak acceleration, Ca = 4.89
General purposeModified sineLow peak velocity (Cv = 1.76) and moderate acceleration
Smooth at high speedCycloidalLowest peak jerk of the common laws
Zero jerk at the ends4-5-6-7 polynomialSmoothest start, but higher acceleration
Blend into constant velocityBlending polynomial or half-cycloidsMatch the constant speed with no jump (Norton Ch. 6)

Peak factors from Norton, Cam Design and Manufacturing Handbook, Table 3-1, and Rothbart, Cam Design Handbook (2004), Fig. 3.2. Compare them on the cam motion laws page.

Norton's rules of thumb (p. 531): modified sine or 3-4-5 are the all-round "workhorse" choices and are better than modified trapezoid once follower vibration counts. For low vibration, 4-5-6-7 or cycloidal. Don't add dwells the machine doesn't need: every stop costs time the moves could have used.
05

Design Steps in Order

  1. Timing: list what the follower must do over one turn: rises, dwells and falls, with angles and lifts.
  2. Motion laws: pick a law for each rise and fall. Check that every join is continuous.
  3. Follower: choose the type, roller size and any offset.
  4. Base circle: make it just big enough to keep the pressure angle under about 30° (translating follower).
  5. Curvature: keep the smallest convex pitch radius above 1.5 to 3 times the roller radius, so the roller (and the cutter) can follow it.
  6. Forces: find the spring rate and preload that keep the follower on the cam at full speed, then the camshaft torque.
  7. Stress: check roller contact stress and roller bearing life.
  8. Make it: export the profile (DXF or points) and choose a cutter smaller than the smallest concave radius.

Steps 2 to 6 run live on the disk cam designer.

06

Glossary

Base circle
The smallest circle tangent to the cam surface.
Prime circle
The smallest circle tangent to the pitch curve: base circle plus roller radius.
Pitch curve
The path of the roller centre (or follower trace point) relative to the cam.
Pressure angle
Angle between the follower's direction of travel and the line of force at the contact.
Dwell
A part of the turn where the follower does not move.
Rise, fall (return)
Follower moving away from, or back toward, the cam centre.
SVAJ
Displacement, velocity, acceleration and jerk: the four curves that describe a motion.
Undercut
Where the pitch curve is sharper than the roller, so the cam cannot give the motion asked for.
Jump (float)
The follower leaving the cam because the spring cannot overcome inertia.
Desmodromic
Positive-drive closure: the cam pushes the follower both ways, with no return spring.
07

Sources

H. A. Rothbart (ed.), Cam Design Handbook, McGraw-Hill, 2004: follower types and classification (Ch. 1), motion curves (Chs. 2–4), pressure angle and radius of curvature (Chs. 6–7), spring surge (Ch. 12). The 30° pressure angle limit is a common rule of thumb, not a standard.

R. L. Norton, Cam Design and Manufacturing Handbook, Industrial Press: double-dwell laws (Ch. 3), single-dwell polynomials (Ch. 4), pressure angle and radius of curvature (Ch. 7), rules of thumb (§18.2, pp. 530–532).