Cam Timing Diagram: Overlay Several Cams on One Machine Cycle, Set Phase and Shaft Ratio, Check Dwell Overlap, and Compare Displacement, Velocity, Acceleration and Jerk

Cam Timing Diagram
Machine and Cams
rpm
ColorNameTypePhase (°) iCam angle at machine 0°. Raising it moves every event of this cam earlier on the machine cycle.Ratio iCam turns per machine cycle, as two whole numbers. 1 : 1 for a cam on the main shaft.Lift

Select a row to edit that cam's motion below. "Open" sends the cam to its designer page; export it there and use Add Cam From File to bring it back.

Motion of
#TypeStartEnd (°)Motion lawLift (in)

Segment angles are this cam's own angles. The timeline places them on the machine cycle with the cam's phase and ratio.

Timeline
0°
CamCam angleSegmentLift

Dots mark where each segment starts, labelled with the machine angle. Solid bands are rises, lighter bands falls, pale bands dwells. Move the pointer over the timeline or drag the slider to read every cam at once.

Drag a cam's row left or right to change its phase. It moves in whole degrees and snaps onto another cam's dots. Hold Shift for 0.1° steps with no snapping. Press Esc to put it back.

Dwell Overlap and Alignment
Dwell overlap

Line up an event
°

Warnings & Status

    Graphs Over the Machine Cycle
    Events on the Machine Cycle
    Cam#SegmentFrom (°)To (°)Length (°)Time (ms)

    Design each cam on its own page: disk, barrel and end, linear. New to cams? Start with the cam design guide.

    For critical applications, check the timing on the machine. This is a free calculator and is not liable for design errors.

    Reference Guide: Cam Timing
    01

    What a Timing Diagram Is For

    A machine with several cams on one main shaft only works when every cam moves at the right moment. One clamp must close before a tool comes down; two feeds must hold still together. A timing diagram puts every cam on the same scale, the machine angle, so those relationships can be read and set.

    Each row is one cam. Its rises, falls and dwells sit where they happen in the machine cycle, and a dot marks the start of each segment with its machine angle.

    The graphs overlay the cams' displacement, velocity, acceleration and jerk on the same machine-angle axis. "Shape" scales each cam to its own peak, so cams with different lifts, or an arm measured in degrees, compare on one plot. "Actual" shows real values; a swinging arm's lift is then in degrees.

    02

    Phase and Ratio

    cam angle = phase + machine angle × ratio

    Phase is the cam's own angle when the machine is at 0°. Raising a cam's phase by 10° makes all its events happen 10° of machine angle earlier (for a 1 : 1 cam).

    Ratio is cam turns per machine cycle. A cam geared 2 : 1 turns twice per cycle, so its pattern appears twice on the timeline, and its velocity, acceleration and jerk against machine angle are 2, 4 and 8 times what its own segment table gives. The ratio must give a whole number of cam turns per cycle, or the motion would not repeat.

    To set a phase by eye, drag the cam's row on the timeline. Dragging right makes its events happen later, which lowers the phase. When one of its dots comes within a few pixels of another cam's dot, it snaps so the two events start at the same machine angle. Type the phase or use Line Up an Event when you need an exact value.

    03

    Dwell Overlap

    Many machines need two followers to hold still at the same time: one part held while another is placed, or two tools that must both be clear. Pick two cams under Dwell Overlap. The tool lists every stretch of the cycle where both are in a dwell, the total in degrees, and the time it lasts at the machine speed.

    The overlapping stretches are shaded on the timeline. To change the overlap, move one cam with its phase, or lengthen a dwell in its segment table and shorten the neighbouring rise or fall. Remember that a shorter rise means higher acceleration; check the graphs after each change.

    04

    Timing an Existing Machine

    To copy the timing of a working machine, measure each follower against the main shaft angle. A degree wheel on the main shaft and a dial indicator on each follower are enough. Note where each follower starts and stops moving, and the lift between.

    Enter each cam's segments from those readings, using its own angles from 0°. Then use Line Up an Event to put one segment start at the machine angle you measured. The tool sets the phase for you.

    Once every cam matches the old machine, change the new design one cam at a time: a new lift, a different law, a longer dwell. Check the overlaps and the acceleration graphs after each step. Design the profiles themselves on the disk, barrel and end, or linear pages, then bring them back with Add Cam From File.

    05

    Example: Four Cams on One Cycle

    The page's starting example: two disk cams and two end cams on a 360° cycle at 120 rpm. Disk cam 2 is phased 340° so its high dwell overlaps disk cam 1's by 80°. Every segment window on the machine cycle:

    Cam#SegmentFrom (°)To (°)Length (°)Time at 120 rpm (ms)
    Disk cam 11Rise0.090.090.0125.0
    Disk cam 12Dwell90.0200.0110.0152.8
    Disk cam 13Fall200.0290.090.0125.0
    Disk cam 14Dwell290.0360.070.097.2
    Disk cam 24′Dwell0.020.020.027.8
    Disk cam 21Rise20.0120.0100.0138.9
    Disk cam 22Dwell120.0240.0120.0166.7
    Disk cam 23Fall240.0320.080.0111.1
    Disk cam 24Dwell320.0360.040.055.6
    End cam 14Dwell0.060.060.083.3
    End cam 11Rise60.0180.0120.0166.7
    End cam 12Dwell180.0240.060.083.3
    End cam 13Fall240.0360.0120.0166.7
    End cam 23′Fall0.030.030.041.7
    End cam 24Dwell30.0180.0150.0208.3
    End cam 21Rise180.0240.060.083.3
    End cam 22Dwell240.0330.090.0125.0
    End cam 23Fall330.0360.030.041.7
    06

    Sources

    Motion laws and their derivatives: see the cam motion laws page and its sources (Rothbart, Cam Design Handbook; Norton, Cam Design and Manufacturing Handbook). The machine-angle mapping is the chain rule applied to each cam's motion.