Linear (Translating) Cam Calculator: Plate Profile, Pressure Angle, Radius of Curvature, Undercut, Follower Spring Force and Drive Force, with STEP, STL, DXF and SolidWorks Curve Export

Linear (Translating) Cam Designer
Cam Plate, Follower & Spring
Cam
in/s
in
in
°
Follower
in
in
lb
Spring & Load
lbf/in
lbf
lbf
–

In a slot there is no spring: the follower force is mass × acceleration plus the external load.

Motion: Segments Along the Travel
#TypeStartEnd (°)Motion lawLift (mm)
Compare motion laws
Results
0°

cam platepitch curveline of force

Warnings & Status

    2D & CAD Exports
    °
    in
    CSV COLUMNS

    Units: the DXF and curve files use the CAD file units above (mm unless you change it), and the unit is in each file name. Curve files carry no units: SolidWorks reads them in the part's units. The plate's bottom edge is y = 0 and its start is x = 0. DXF: the closed plate outline, the pitch curve and, for a slot, the other wall. Curve: Insert › Curve › Curve Through XYZ Points, then Convert Entities and close the outline down to the base. The CSV adds a position column.

    3D Exports
    in
    ×

    Both files are in millimetres, whichever units are selected. The plate lies in the XY plane with its thickness along Z. The first STEP export downloads the CAD kernel (about 50 MB). A slot plate's second wall is in the DXF; the 3D files show the plate edge only.

    Graphs

    Negative values are concave parts of the cam. Very large values (nearly flat) are left off the plot.

    With spring closure, below zero means the follower lifts off the plate.

    3D Model

    Drag to orbit, scroll to zoom. Shows the part as it will export, including the scale.

    Print Data Sheet prints the cam on three pages: a scale drawing with the inputs, motion program, results and checks; the motion and force graphs; and a point table every 10°. Pressing Ctrl+P on this page prints the same sheet.

    Running several cams on one shaft? Line them up on the cam timing diagram: save this cam with Export, then use Add Cam From File there.

    New to cams? Start with the cam design guide. Rotating cams: disk and barrel cam designers.

    For critical applications, check the results by hand or with another cam program. This is a free calculator and is not liable for design errors.

    Forces assume a rigid follower train and no friction. Contact stress assumes steel on steel.

    Reference Guide: Linear Cam Design
    01

    What a Linear Cam Is

    A linear (translating) cam is a plate whose edge is shaped to the motion you want. The plate slides along its length and the follower, riding on the edge, moves across it. They are used where a straight stroke already exists: slides, presses, gauges and pattern-following tools.

    Same math as a barrel cam

    Unroll a barrel cam and you get a linear cam. A plate with travel L acts like a barrel of radius Re = L / 2π. This page and the barrel cam designer share their geometry code and give the same answers.

    02

    Travel, Speed and the Motion Program

    The segment table runs from 0 to the travel length. The motion laws are the same as on the other cam pages; a rise over 2 in of a 10 in travel is the same shape as a rise over 72° of a turn.

    Cam speed sets time: one pass takes travel ÷ speed. Velocities, accelerations and forces follow from that.

    A linear cam makes one pass, so it does not have to end at the lift it started from, and the tool does not check the join between its two ends. If the plate runs back and forth, the return stroke reads the same edge backwards.

    03

    Pressure Angle

    The pressure angle is simply the slope of the pitch curve:

    φ = atan(dy/dx) = atan(s′ / Re), Re = L / 2π

    It is Norton's barrel-cam Eq. 7.4 (p. 158) with the travel in place of the circumference. Keep it under about 30° for a sliding follower.

    To lower it, lengthen the travel or spread the rise over more of it. The tool shows the shortest travel that holds your limit for the same motion program.

    04

    Radius of Curvature and Undercut

    The pitch curve's radius of curvature is Norton's Eq. 7.21 (p. 173) with Re in place of Rp. On a crest the cam surface is convex with radius ρ − Rf. If ρ is smaller than the roller radius there, the surface folds over: undercut.

    Norton keeps ρ at 1.5 to 3 times the roller radius, above 2 by preference (p. 166 and rule 7, p. 531). Valleys are concave and cannot undercut a spring-closed plate. For a slot, both walls count.

    05

    Follower Force and Drive Force

    F = m·a + c·v + k·s + F0 + Fext

    The force normal to the plate edge is F / cos φ. The force needed to push the plate along is F·tan φ, from power balance. That is the "drive force" in the results and on the last graph.

    With spring closure, the contact force must stay above zero or the follower lifts off the plate. In a slot, the roller changes walls wherever F changes sign. Contact stress uses Norton's line-contact equations (Ch. 12), steel on steel.

    06

    Example Cam, Every 10° of the Program

    The calculator's starting example: 10 in (254 mm) of travel at 10 in/s, ½ in of plate under a 1 in roller (½ in radius, ⅝ in wide). Cycloidal rise of ¾ in (19.05 mm) over the first third of the travel, dwell, modified-sine fall, dwell. 1.5 lb follower, 25 lbf/in spring with 10 lbf preload. The table steps every 10° of the program, which is 0.278 in of travel.

    Position (in)Lift (in)Lift (mm)Velocity (in/s)Accel. (in/s²)Pressure angle (°)Pitch radius of curvature (in)Follower force (lbf)Drive force (lbf)
    0.0000.00000.000.000.00.00—10.000.00
    0.2780.00280.070.3021.21.73-4.72210.170.31
    0.5560.02160.551.1236.76.42-2.77410.751.21
    0.8330.06811.732.2542.412.68-2.53912.012.70
    1.1110.14663.723.3736.718.65-3.20114.024.73
    1.3890.25286.424.2021.222.78-6.01616.667.00
    1.6670.37509.534.500.024.23—19.668.84
    1.9440.497212.634.20-21.222.786.01622.619.49
    2.2220.603415.333.38-36.718.653.20125.158.49
    2.5000.681917.322.25-42.412.682.53927.026.08
    2.7780.728418.501.12-36.76.422.77428.143.17
    3.0560.747218.980.30-21.21.734.72228.620.86
    3.3330.750019.050.000.00.00—28.750.00
    3.6110.750019.050.000.00.00—28.750.00
    3.8890.750019.050.000.00.00—28.750.00
    4.1670.750019.050.000.00.00—28.750.00
    4.4440.750019.050.000.00.00—28.750.00
    4.7220.750019.050.000.00.00—28.750.00
    5.0000.750019.050.000.00.00—28.750.00
    5.2780.745218.93-0.49-32.3-2.833.10628.47-1.41
    5.5560.717718.23-1.51-36.7-8.562.81427.71-4.17
    5.8330.662116.82-2.47-32.3-13.903.38326.27-6.50
    6.1110.581914.78-3.26-24.0-18.084.85324.25-7.92
    6.3890.483312.28-3.78-12.8-20.719.57421.80-8.24
    6.6670.37509.53-3.960.0-21.60—19.13-7.57
    6.9440.26676.77-3.7812.8-20.71-9.57416.48-6.23
    7.2220.16814.27-3.2624.0-18.08-4.85314.09-4.60
    7.5000.08792.23-2.4732.3-13.90-3.38312.17-3.01
    7.7780.03230.82-1.5136.7-8.56-2.81410.86-1.63
    8.0560.00480.12-0.4932.3-2.83-3.10610.21-0.51
    8.3330.00000.000.000.00.00—10.000.00
    8.6110.00000.000.000.00.00—10.000.00
    8.8890.00000.000.000.00.00—10.000.00
    9.1670.00000.000.000.00.00—10.000.00
    9.4440.00000.000.000.00.00—10.000.00
    9.7220.00000.000.000.00.00—10.000.00
    07

    Sources

    R. L. Norton, Cam Design and Manufacturing Handbook: Eq. 7.4 (p. 158) and Eq. 7.21 (p. 173), written for a barrel cam and applied here with Re = L / 2π; the curvature rule (p. 166 and rule 7, p. 531); line contact (Ch. 12). Motion laws: see the cam motion laws page.